Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
techtalk:ih:engctl03a [2023/12/31 18:42] hippysmack |
techtalk:ih:engctl03a [2023/12/31 18:43] (current) hippysmack |
||
|---|---|---|---|
| Line 9: | Line 9: | ||
| {{:techtalk:ih:engctl:1968_kicker_cover_inside_1_by_dirtyharry68.jpg?direct&400|}} ((photo by DirtyHarry68 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/192529-kicker-cover-roll-pin?t=2061986&page=2)) \\ | {{:techtalk:ih:engctl:1968_kicker_cover_inside_1_by_dirtyharry68.jpg?direct&400|}} ((photo by DirtyHarry68 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/192529-kicker-cover-roll-pin?t=2061986&page=2)) \\ | ||
| - | * Most of the advice on this is probably good for larger size pins and did not work for this situation including: ((DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2061986&page=2 )) | + | * Most of the advice on this is probably good for larger size pins and did not work for this situation including: ((DirtyHarry68 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/192529-kicker-cover-roll-pin?t=2061986&page=2)) |
| * Pick = no good | * Pick = no good | ||
| * Heat / pick = no good, it’s jammed. | * Heat / pick = no good, it’s jammed. | ||
| Line 17: | Line 17: | ||
| * Try annealing pin to allow drilling = maybe a jeweler's torch setup would be good for this. | * Try annealing pin to allow drilling = maybe a jeweler's torch setup would be good for this. | ||
| * Other trial methods might include: | * Other trial methods might include: | ||
| - | * A long drill bit to go through the center of the roll pin and out the bottom. ((brucstoudt of the XLFORUM http://xlforum.net/forums/showthread.php?t=2061986&page=2)) | + | * A long drill bit to go through the center of the roll pin and out the bottom. ((brucstoudt of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/192529-kicker-cover-roll-pin?t=2061986&page=2)) |
| * A left handed drill bit ((MXHD55U of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/192529-kicker-cover-roll-pin/page2?postid=5650610#post4171283)) | * A left handed drill bit ((MXHD55U of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/192529-kicker-cover-roll-pin/page2?postid=5650610#post4171283)) | ||
