Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:ref:paint06 [2019/08/04 21:39] hippysmack [Using KG Industries Stock Kote] |
techtalk:ref:paint06 [2024/01/19 15:22] (current) hippysmack |
||
---|---|---|---|
Line 2: | Line 2: | ||
====== REF: Custom Painting ====== | ====== REF: Custom Painting ====== | ||
\\ | \\ | ||
+ | ====== Painting - Gun Coatings ====== | ||
+ | \\ | ||
+ | \\ | ||
+ | |||
====== Using KG Industries Stock Kote ====== | ====== Using KG Industries Stock Kote ====== | ||
+ | KG Coatings web site: [[https://shop.kgcoatings.com/kg/]] | ||
+ | |||
These were done with KG Industries Stock Kote 1201S Air Cure Satin Black. \\ | These were done with KG Industries Stock Kote 1201S Air Cure Satin Black. \\ | ||
Line 11: | Line 17: | ||
|{{:techtalk:ref:paint:using_kg_stock_kote_1_by_bustakneecap.jpg?direct&300|}}| | |{{:techtalk:ref:paint:using_kg_stock_kote_1_by_bustakneecap.jpg?direct&300|}}| | ||
- | Following directions, the paint was applied in six to seven very light coats at 35 psi. \\ | + | Following directions, the paint was applied in six to seven very light coats with a paint gun at 35 psi. \\ |
The hair dryer was used to keep the parts warm in between coats. \\ | The hair dryer was used to keep the parts warm in between coats. \\ | ||
Line 21: | Line 27: | ||
(for ten minutes or so to heat the aluminum all the way through) \\ | (for ten minutes or so to heat the aluminum all the way through) \\ | ||
- | | The process. ((photos by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?t=1421886)) ||| | + | If the parts are warm it tacks up almost instantly. \\ |
+ | It goes on pretty thin (first three coats were light enough to still see metal through them. \\ | ||
+ | Later, the parts were warmed the hair dryer, sprayed using an airbrush then dried with the hair dryer. \\ | ||
+ | As for dust, just keep the parts on clean paper and the dryer close to the part. \\ | ||
+ | |||
+ | |||
+ | | The process. ((photos by bustakneecap of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-styles/sportster-motorcycle-custom-finishing/132716-gun-kote-1200?t=1421886)) ||| | ||
|{{:techtalk:ref:paint:using_kg_stock_kote_2_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_3_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_4_by_bustakneecap.jpg?direct&300|}}| | |{{:techtalk:ref:paint:using_kg_stock_kote_2_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_3_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_4_by_bustakneecap.jpg?direct&300|}}| | ||
- | | The finished products. ((photos by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?t=1421886)) || | + | | The finished products. ((photos by bustakneecap of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-styles/sportster-motorcycle-custom-finishing/132716-gun-kote-1200?t=1421886)) || |
|{{:techtalk:ref:paint:using_kg_stock_kote_5_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_6_by_bustakneecap.jpg?direct&300|}}| | |{{:techtalk:ref:paint:using_kg_stock_kote_5_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_6_by_bustakneecap.jpg?direct&300|}}| | ||
|{{:techtalk:ref:paint:using_kg_stock_kote_7_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_8_by_bustakneecap.jpg?direct&300|}}| | |{{:techtalk:ref:paint:using_kg_stock_kote_7_by_bustakneecap.jpg?direct&300|}}|{{:techtalk:ref:paint:using_kg_stock_kote_8_by_bustakneecap.jpg?direct&300|}}| |