Differences

This shows you the differences between two versions of the page.

--- techtalk:ref:tools032 [2021/02/21 00:12]
hippysmack [Common Brake Line Threads]
+++ techtalk:ref:tools032 [2022/03/27 03:08]
hippysmack [Metric Nut/Bolt Threads]
@@ Line 1: / Line 1: @@
 [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
-====== REF: Thread Identification and Sizing Charts ======
+====== REF: Tools & Fasteners ======
+====== Thread Identification and Sizing Charts ======
 \\
 ====== Measuring Threads In General ======
@@ Line 41: / Line 43: @@
 You can download full size charts from the net if needed. \\
 These are just for quick reference. \\
+====== Pitch to TPI Conversion Table ======
+The table below is a reprint from THA ((https://traininghandsacademy.com/wp-content/uploads/2020/11/Pitch-mm-to-TPI-inches-Conversion-Table.pdf)) \\
+^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&600|}}||||||
+|  MM per thread (Pitch) = Threads per inch (TPI)  ||||||
+|Pitch (mm)|Pitch (in)|Treads Per Inch|Pitch (mm)|Pitch (in)|Treads Per Inch|
+|0.2|0.0079|127.00|1.25|0.0492|20.32|
+|0.25|0.0098|101.60|1.5|0.0591|16.93|
+|0.3|0.0118|84.67|1.75|0.0689|14.51|
+|0.35|0.0138|72.57|2.0|0.0787|12.70|
+|0.4|0.0157|63.50|2.5|0.0984|10.16|
+|0.45|0.0177|56.44|3.0|0.1181|8.47|
+|0.5|0.0197|50.80|3.5|0.1378|7.26|
+|0.6|0.0236|42.33|4.0|0.1575|6.35|
+|0.7|0.0276|36.29|4.5|0.1772|5.64|
+|0.75|0.0295|33.78|5.0|0.1969|5.08|
+|0.8|0.0315|31.75|5.5|0.2165|4.62|
+|1.0|0.0394|25.40|6.0|0.2362|4.23|
 ====== US Nut/Bolt Threads ======
@@ Line 57: / Line 79: @@
     * This will give you the TPI (or second number).
-^  US Thread Pitch  |||||||||
+^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&600|}}|||||||||
+|  US Thread Pitch  |||||||||
 |Bolt (nominal) \\ Diameter|Decimal|TPI \\ (course)|TPI \\ (fine)^  |Bolt (nominal) \\ Diameter|Decimal|TPI \\ (course)|TPI \\ (fine)|
 |**1/4"**|.25"|20|28^  |**3/4"**|.75"|10|16|
@@ Line 74: / Line 97: @@
 The diameter is the outside diameter of the thread peaks. \\
-In this example of a 10mm bolt; M10x1.25x35 states that the diameter of the threads is 10mm, the thread pitch is 1.25mm and it's 35mm long. \\
+In example of a 10mm bolt; M10x1.25x35 states that the diameter of the threads is 10mm, the thread pitch is 1.25mm and it's 35mm long. \\
-|  Metric Thread Pitch  ||||
+^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&600|}}|||||
-|Bolt Diameter|Standard Thread Pitch (mm)|Fine Thread Pitch (mm)|Extra Fine Thread Pitch (mm)|
+|  Metric Thread Pitch  |||||
-|**4mm**|0.70|  -  |  -  |
+|Thread OD \\ Metric|Thread OD \\ Inches (app)|Standard \\ Pitch (mm)|Fine \\ Pitch (mm)|Extra Fine \\ Pitch (mm)|
-|**5mm**|0.80|  -  |  -  |
+|**4mm**|0.157"|0.70|  -  |  -  |
-|**6mm**|1.00|  -  |  -  |
+|**5mm**|0.197"|0.80|  -  |  -  |
-|**7mm**|1.00|  -  |  -  |
+|**6mm**|0.236"|1.00|  -  |  -  |
-|**8mm**|1.25|  1.00  |  -  |
+|**7mm**|0.275"|1.00|  -  |  -  |
-|**10mm**|1.50|  1.25  |  1.00  |
+|**8mm**|0.315"|1.25|  1.00  |  -  |
-|**12mm**|1.75|  1.50  |  1.25  |
+|**10mm**|0.394"|1.50|  1.25  |  1.00  |
-|**14mm**|2.00|  1.50  |  -  |
+|**12mm**|0.472"|1.75|  1.50  |  1.25  |
-|**16mm**|2.00|  -  |  -  |
+|**14mm**|0.551"|2.00|  1.50  |  -  |
-|**18mm**|2.50|  -  |  -  |
+|**16mm**|0.630"|2.00|  -  |  -  |
-|**20mm**|2.50|  -  |  -  |
+|**18mm**|0.708"|2.50|  -  |  -  |
-|**24mm**|3.00|  -  |  -  |
+|**20mm**|0.787|2.50|  -  |  -  |
+|**24mm**|  |3.00|  -  |  -  |
+Metric screw thread OD can be deduced by using an imperial (US) scale caliper using the chart above. \\
+Your measurements may not be an exact match to the dims above but will be close enough to make a judgement on the metric counterpart size. \\
+{{:techtalk:ref:tools:measuring_metric_screw_threads_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
 ====== Common Brake Line Threads ======
 Most brake systems use flared fittings since they have strong metal to metal connections. \\
@@ Line 109: / Line 137: @@
 It will catch the first thread, making you think that it will go in, but it will destroy the threads as you tighten it. \\
+^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&600|}}|||
 |  Thread Conversion Comparisons  |||
 |Thread Size|Metric Diameter|Metric Thread Pitch|
@@ Line 115: / Line 144: @@
 |7/16" x 24|11.1125mm|1.05833333mm|
 |M12 x 1.0|12mm|1.0mm|
 ====== NPT Pipe Threads ======
@@ Line 136: / Line 163: @@
     * The sizes in the chart below are the major dia of the male straight thread (as the pipe OD is the major). \\ And the major dia. of a tapered male thread at it's big end. ((DR DICK of the XLFORUM  http://xlforum.net/forums/showthread.php?t=1810036&highlight=tap+die&page=2))
-    * The tapered thread has it's diameter reduced on a taper of .0625 per inch of thread length. Almost all hardware store fittings will be tapered thread.((DR DICK of the XLFORUM  http://xlforum.net/forums/showthread.php?t=1810036&highlight=tap+die&page=2))
+    * The tapered thread has it's diameter reduced on a taper of .0625" per inch of thread length. Almost all hardware store fittings will be tapered thread.((DR DICK of the XLFORUM  http://xlforum.net/forums/showthread.php?t=1810036&highlight=tap+die&page=2))
+^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&600|}}||||
 |Nominal pipe \\ size (NPT) \\ (male threads)|Threads \\ per inch|Actual outside \\ diameter, (OD)||
 |:::|:::|Inch|MM|
@@ Line 154: / Line 182: @@
 {{:techtalk:ref:tools:measuring_fitting_tpi_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:tools:measuring_fitting_tpi-2_by_hippysmack.jpg?direct&300|}} ((photos by Hippysmack)) \\
-====== JIC Flared Fitting Threads ======
+====== AN and JIC Flared Fitting Threads ======
+==== AN ====
+AN (or Army/Navy) was never intended to characterize an entire fluid system, and is mostly designed as a thread specification. \\
+AN fittings are flared fittings with a 37° chamfer seating surface and straight threads. \\
+They can also be reused many times unless the seats are damaged. \\
+AN sizes range from -2 to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1/16" increments. \\ This system does not specify the inside diameter of the tubing because the tube wall can vary in thickness. ((http://www.anfittingsdirect.com/an-fittings-and-stainless-steel-lines-a-an_fittings_sizes.html)) \\
+  * You can measure male AN or JIC threads by either using a caliper or simply laying a fitting across a tape measure. \\ Measure the OD of the threads and count the number of threads per inch to confirm with the chart below. \\ Thread OD will not exactly match the SAE thread size but will get you close enough if you have a AN fitting.
+==== JIC ====
 JIC (Joint Industry Council) fittings are flared fittings with a 37° chamfer seating surface and straight threads. ((https://www.hydrauliconline.com/hydraulic-hose-fittings/what-is-a-jic-fitting/)) \\
 The JIC fitting uses it's flared seating surface to seal, instead of an O-ring that could corrode or NPTF fittings. \\
@@ Line 166: / Line 202: @@
   * You can measure male JIC threads by either using a caliper or simply laying a fitting across a tape measure. \\ Measure the OD of the threads and count the number of threads per inch to confirm with the chart below. \\ Thread OD will not exactly match the SAE thread size but will get you close enough if you have a JIC fitting.
+^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&600|}}|||||
 |JIC Size|AN Size|Thread \\ Size|Male \\ Thread O.D.|Female \\ Thread O.D|
-|1/8"|-2|5/16"-24|5/16" (.31")|9/32" (.27")|
+|1/8"|-2|5/16"-24|5/16"|9/32"|
-|3/16"|-3|3/8"-24|3/8" (.38")|11/32" (.34")|
+|3/16"|-3|3/8"-24|3/8"|11/32"|
-|1/4"|-4|7/16"-20|7/16" (.44")|13/32" (.39")|
+|1/4"|-4|7/16"-20|7/16"|13/32"|
-|5/16"|-5|1/2"-20|1/2" (.50"|15/32" (.45")|
+|5/16"|-5|1/2"-20|1/2"|15/32"|
-|3/8"|-6|9/16"-18|9/16" (.56")|17/32" (.51")|
+|3/8"|-6|9/16"-18|9/16"|17/32"|
-|1/2"|-8|3/4"-16|3/4" (.75")|11/16" (.69")|
+|1/2"|-8|3/4"-16|3/4"|11/16"|
-|5/8"|-10|7/8"-14|7/8" (.88")|13/16" (.81")|
+|5/8"|-10|7/8"-14|7/8" |13/16"|
-|3/4"|-12|1-1/16"-12|11/16" (1.06")|1" (.98")|
+|3/4"|-12|1-1/16"-12|11/16"|1"|
-|7/8"|-14|1-3/16"-12|1-3/16" (1.19")|1-1/8" (1.10")|
+|7/8"|-14|1-3/16"-12|1-3/16"|1-1/8"|
-|1"|-16|1-5/16-12|1-5/16" (1.31")|1-1/4" (1.23")|
+|1"|-16|1-5/16-12|1-5/16"|1-1/4"|
-====== AN Flared Fitting Threads ======
-AN (or Army/Navy) was never intended to characterize an entire fluid system, and is mostly designed as a thread specification. \\
-AN fittings are flared fittings with a 37° chamfer seating surface and straight threads. \\
-They can also be reused many times unless the seats are damaged. \\
-AN sizes range from -2 to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1/16" increments. \\ This system does not specify the inside diameter of the tubing because the tube wall can vary in thickness. ((http://www.anfittingsdirect.com/an-fittings-and-stainless-steel-lines-a-an_fittings_sizes.html)) \\
-  * You can measure male AN threads by either using a caliper or simply laying a fitting across a tape measure. \\ Measure the OD of the threads and count the number of threads per inch to confirm with the chart below. \\ Thread OD will not exactly match the SAE thread size but will get you close enough if you have a AN fitting.
-^AN Size^Metal Tube OD^Nearest SAE Thread Size ((Information provided by 4th of July of the XLFORUM http://xlforum.net/forums/showthread.php?t=1923879)) ^
-|-3|3/16"|3/8"-24|
-|-4|1/4"|7/16"-20|
-|-5|5/16"|1/2"-20|
-|-6|3/8"|9/16"-18|
-|-8|1/2"|3/4"-16|
-|-10|5/8"|7/8"-14|
-|-12|3/4"|1-1/16"-12|
-|-16|1"|1-5/16"-12|
 \\

Trace:

Differences

Navigation

Search

Toolbox