Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:elec02b [2019/11/14 00:30] hippysmack [Removing the stator] |
techtalk:evo:elec02b [2019/11/14 00:31] hippysmack [Remove the clutch release assembly] |
||
|---|---|---|---|
| Line 33: | Line 33: | ||
| {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | ===== Loosen the primary chain adjuster ===== | ||
| + | Loosening the primary chain adjuster takes the pressure off the primary chain from the cover. \\ | ||
| + | Hold the stud with a 1/4" Allen wrench and use a 7/8" open end wrench to loosen the tightening nut. \\ | ||
| + | Once the nut is loose, unscrew the stud until it bottoms out to loosen the chain adjuster. \ | ||
| + | This is easier done before removing the cover since the engine holds the assembly in place. \\ | ||
| + | If you don't loosen this before re-installing the cover, it will be more difficult to install the cover later. \\ | ||
| + | |||
| + | {{:techtalk:evo:engmech:removing_primary_cover_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| ===== Clutch cable ===== | ===== Clutch cable ===== | ||
| Line 66: | Line 76: | ||
| {{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_12_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_13_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_12_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_13_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| - | ===== Loosen the primary chain adjuster ===== | ||
| - | Loosening the primary chain adjuster takes the pressure off the primary chain from the cover. \\ | ||
| - | Hold the stud with a 1/4" Allen wrench and use a 7/8" open end wrench to loosen the tightening nut. \\ | ||
| - | Once the nut is loose, unscrew the stud until it bottoms out to loosen the chain adjuster. \ | ||
| - | This is easier done before removing the cover since the engine holds the assembly in place. \\ | ||
| - | If you don't loosen this before re-installing the cover, it will be more difficult to install the cover later. \\ | ||
| - | |||
| - | {{:techtalk:evo:engmech:removing_primary_cover_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| ====== Loosen and remove the primary cover ====== | ====== Loosen and remove the primary cover ====== | ||
