Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ih:carb07 [2019/09/21 19:22] hippysmack [IH: Carburetor, Intake Manifold & Exhaust] |
techtalk:ih:carb07 [2021/08/01 21:58] ixl2relax |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| ====== Intake Manifold ====== | ====== Intake Manifold ====== | ||
| + | |||
| + | ===== Seals - Intake to Heads ===== | ||
| + | |||
| + | ^ Intake to Head - Hardware History. ((See Brucstoudt & Dr_Dick - XLForum - http://xlforum.net/forums/showthread.php?t=2079889)) | | ||
| + | | 57-78 had the exact same port sealing machining, heads and manifolds - **They use O-rings**. | | ||
| + | | 1979 is confusing because it had the o-ring machining but **it used rubber bands**. | | ||
| + | | 80-later had the "o-ring delete" machining. **These use the rubber bands**.| | ||
| + | | | | ||
| + | | (If you had a 79 you could retro fit 78-earlier interface mechanisms as a bolt on.) | | ||
| + | | 80-later needed the heads to be machined if you wanted to go back to the straight up o-ring seals. | | ||
| + | |||
| + | |||
| ===== Bendix ===== | ===== Bendix ===== | ||
| {{:techtalk:ih:carb:bendix_mounting_hardware_by_the_doctor71.jpg?direct&300|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) \\ | {{:techtalk:ih:carb:bendix_mounting_hardware_by_the_doctor71.jpg?direct&300|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) \\ | ||
| Line 11: | Line 23: | ||
| {{:techtalk:ih:carb:bendix_-_mounted_1_by_the_doctor71.jpg?direct&200|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) {{:techtalk:ih:carb:bendix_-_mounted_2_by_the_doctor71.jpg?direct&200|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) {{:techtalk:ih:carb:bendix_-_mounted_3_by_the_doctor71.jpg?direct&200|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) \\ | {{:techtalk:ih:carb:bendix_-_mounted_1_by_the_doctor71.jpg?direct&200|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) {{:techtalk:ih:carb:bendix_-_mounted_2_by_the_doctor71.jpg?direct&200|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) {{:techtalk:ih:carb:bendix_-_mounted_3_by_the_doctor71.jpg?direct&200|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071371)) \\ | ||
| + | ===== Keihin Butterfly ===== | ||
| + | These V-twin clamps (35-0419) work well for stopping intake leaks. The tool to install them is the same as any oiteker clamp pliers. ((66xlch of the XLFORUM http://xlforum.net/forums/showthread.php?t=1079081&page=5)) \\ | ||
| + | {{:techtalk:ih:carb:manifold_clamps_by_66xlch.jpg?direct&300|}} ((photo by 66xlch of the XLFORUM http://xlforum.net/forums/showthread.php?t=1079081&page=5)) {{:techtalk:ih:carb:manifold_clamps_by_dirtycory.jpg?direct&300|}} ((photo by DirtyCory of the XLFORUM http://xlforum.net/forums/showthread.php?t=1079081&page=7)) \\ | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
