Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:ref:oil05g [2019/08/17 00:47]
hippysmack [norseXL's 1986 Engine Oiling Mods]
techtalk:ref:oil05g [2019/08/17 01:06]
hippysmack [norseXL's 1986 Engine Oiling Mods]
Line 16: Line 16:
 A windage tray was made with a 2mm thick aluminum plate to also act as a flywheel scraper. \\ A windage tray was made with a 2mm thick aluminum plate to also act as a flywheel scraper. \\
 The front part was bent toward the fly-wheels after the pic below was taken. ((norseXL of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1833647)) \\ The front part was bent toward the fly-wheels after the pic below was taken. ((norseXL of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1833647)) \\
 +The bolts are secured with Loctite (2701). \\ 
  
 |  Reed valve. ((photo by norseXL of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1386341)) ​ |  Homemade windage tray. ((photo by norseXL of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1386341)) ​ | |  Reed valve. ((photo by norseXL of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1386341)) ​ |  Homemade windage tray. ((photo by norseXL of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1386341)) ​ |
-|{{:​techtalk:​ref:​oil:​reed_valve_by_norsexl.jpg?​direct&​300|}}|{{:​techtalk:​ref:​oil:​homemade_windage_tray_by_norsexl.jpg?​direct&​300|}}| ​ +|{{:​techtalk:​ref:​oil:​reed_valve_by_norsexl.jpg?​direct&​300|}}|{{:​techtalk:​ref:​oil:​homemade_windage_tray_by_norsexl.jpg?​direct&​300|}}| 
 + 
 +Cam box oiling was also modified. \\ 
 +A line was tapped into the bottom of the case so the oil level doesn'​t rise above the castings for the bolts to flow to the scavenge hole at the rear of the crankcase. \\ 
 +Also an external drain was plumbed from the cam chest to the crankcase (under the windage-plate). \\ 
 + 
 +|{{:​techtalk:​ref:​oil:​lowering_oil_level_in_cam_box_floor_by_norsexl.jpg?​direct&​300|}}|{{:​techtalk:​ref:​oil:​external_cam_floor_drain_by_norsexl.jpg?​direct&​300|}}|
 ====== Rubine'​s Mod to Move Oil Scavenging to the Front on an S&S Pro Stock Case ====== ====== Rubine'​s Mod to Move Oil Scavenging to the Front on an S&S Pro Stock Case ======
 Article by Rubine of the XLFORUM ((http://​xlforum.net/​forums/​showthread.php?​t=1861960&​page=16)) \\ Article by Rubine of the XLFORUM ((http://​xlforum.net/​forums/​showthread.php?​t=1861960&​page=16)) \\