Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:oil13 [2019/03/10 23:38] hippysmack [Modifying a standard motor mount for use as a oil filter mount] |
techtalk:ref:oil13 [2019/03/18 04:09] hippysmack [Other forward positions] |
||
|---|---|---|---|
| Line 103: | Line 103: | ||
| * Tap using a standard 3/4"x16 bit. | * Tap using a standard 3/4"x16 bit. | ||
| * **Make the filter adapter**. | * **Make the filter adapter**. | ||
| - | * Drill and tap a hole through the center of a 3/4"x16 bolt: | + | * Drill and tap a hole through the entire center of a 3/4"x16 bolt: |
| * This hole will be for filtered oil feed out to the oil tank: | * This hole will be for filtered oil feed out to the oil tank: | ||
| * The bolt needs to be center drilled with a 7/16" (.4375") drill bit in steps. \\ (pre-drill hole size for another a 1/4" NPT to 3/8" hose barb fitting for the feed hose to the oil tank). | * The bolt needs to be center drilled with a 7/16" (.4375") drill bit in steps. \\ (pre-drill hole size for another a 1/4" NPT to 3/8" hose barb fitting for the feed hose to the oil tank). | ||
| Line 146: | Line 146: | ||
| |{{:techtalk:ref:oil:remote_oil_filter_2_by_ddddylan.jpg?direct&300|}}|{{:techtalk:ref:oil:remote_oil_filter_1_by_ddddylan.jpg?direct&300|}}| | |{{:techtalk:ref:oil:remote_oil_filter_2_by_ddddylan.jpg?direct&300|}}|{{:techtalk:ref:oil:remote_oil_filter_1_by_ddddylan.jpg?direct&300|}}| | ||
| - | ---- | + | |
| + | -------- | ||
| This is an after market filter and cooler setup on a 77 model. ((photo by BLIGHT of the XLFORUM http://xlforum.net/forums/showthread.php?t=578083)) \\ | This is an after market filter and cooler setup on a 77 model. ((photo by BLIGHT of the XLFORUM http://xlforum.net/forums/showthread.php?t=578083)) \\ | ||
| The filter adapter is 5/"x24. However, you can buy adapters online to increase the adapter size to 13/16" or 3/4". \\ | The filter adapter is 5/"x24. However, you can buy adapters online to increase the adapter size to 13/16" or 3/4". \\ | ||
| |{{:techtalk:ref:oil:oil_filter_and_cooler_by_blight.jpg?direct&250|}}| | |{{:techtalk:ref:oil:oil_filter_and_cooler_by_blight.jpg?direct&250|}}| | ||
| + | |||
| + | ---- | ||
| + | |||
| + | This reportedly an old drag specialties item from the early eighty's. ((hasselme0 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1078240&page=3)) ((photos by 78ironhead of the XLFORUM http://xlforum.net/forums/showthread.php?t=1078240&page=3)) \\ | ||
| + | It uses the older felt type filters made for early shovels and is a cooler/filter all in one. \\ | ||
| + | |{{:techtalk:ref:oil:oil_filter_-_cooler_2_by_78ironhead.jpg?direct&300|}}|{{:techtalk:ref:oil:oil_filter_-_cooler_4_by_78ironhead.jpg?direct&300|}}| | ||
| + | |||
| + | |{{:techtalk:ref:oil:oil_filter_-_cooler_1_by_78ironhead.jpg?direct&300|}}|{{:techtalk:ref:oil:oil_filter_-_cooler_3_by_78ironhead.jpg?direct&300|}}| | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| ====== Rear mounted filters ====== | ====== Rear mounted filters ====== | ||
