Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:genmsr04 [2020/10/27 04:39] hippysmack [Timing Hole Plug (57-03)] |
techtalk:ref:genmsr04 [2020/10/30 00:30] hippysmack [Modified Oil Tank Cap] |
||
---|---|---|---|
Line 1: | Line 1: | ||
[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
- | ====== REF: Engine Mechanicals - Sub-04F ====== | + | ====== REF: General-MSR 04 ====== |
\\ | \\ | ||
====== Using / Diagnosing with a Slack Tube (Manometer) ====== | ====== Using / Diagnosing with a Slack Tube (Manometer) ====== | ||
Line 8: | Line 8: | ||
* [[techtalk:ref:tools173#manometer_slack_tube_for_measuring_air_pressure|Manometer (slack tube) for Measuring Air Pressure]] (what it is and how it works) | * [[techtalk:ref:tools173#manometer_slack_tube_for_measuring_air_pressure|Manometer (slack tube) for Measuring Air Pressure]] (what it is and how it works) | ||
* [[techtalk:ref:engmech04e|Building Your Own Slack Tube]] | * [[techtalk:ref:engmech04e|Building Your Own Slack Tube]] | ||
+ | * [[techtalk:ref:genmsr04a|Modifying a Rubber Stopper for Oil Tank Pressure Testing]] | ||
* [[techtalk:ref:engmech04g|Slack Tube Testing on a 1998 1250S Sportster]] | * [[techtalk:ref:engmech04g|Slack Tube Testing on a 1998 1250S Sportster]] | ||
* [[techtalk:ref:engmech07p|Testing with a Slack Tube (Manometer) by bustert]] | * [[techtalk:ref:engmech07p|Testing with a Slack Tube (Manometer) by bustert]] | ||
Line 71: | Line 72: | ||
|6000 \\ RPM|{{:techtalk:ref:engmech:checking_cc_pressure_at_timing_hole_plug_6_by_bustert.jpg?direct&300|}}|{{:techtalk:ref:engmech:checking_cc_pressure_at_oil_tank_6_by_bustert.jpg?direct&300|}}|6000 \\ RPM| | |6000 \\ RPM|{{:techtalk:ref:engmech:checking_cc_pressure_at_timing_hole_plug_6_by_bustert.jpg?direct&300|}}|{{:techtalk:ref:engmech:checking_cc_pressure_at_oil_tank_6_by_bustert.jpg?direct&300|}}|6000 \\ RPM| | ||
+ | ==== Modified Oil Tank Cap ==== | ||
+ | You can drill a hole for an NPT fitting in a spare oil cap or make a cap just for testing. \\ | ||
+ | The one below was made from a rubber plug bought at Lowes. [[techtalk:ref:genmsr04a|Click here]] to see the pics of the mod. \\ | ||
+ | |||
+ | {{:techtalk:ref:genmsr:homemade_test_oil_cap_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | If you're testing the 04-up plastic oil tank for high pressure, the oil cap is not going to be helpful as a test point. \\ | ||
+ | You need a tee installed in the vent line for that. \\ | ||
====== Testing crankcase pressure ====== | ====== Testing crankcase pressure ====== | ||