Differences

This shows you the differences between two versions of the page.

--- techtalk:ih:carb01k [2019/09/26 02:57]
hippysmack [27155-72B]
+++ techtalk:ih:carb01k [2020/05/01 04:47]
hippysmack [015110 and 015112]
@@ Line 1: / Line 1: @@
 [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
-====== IH: Carburetor, Intake Manifold & Exhaust Systems - Sub-01K ======
+====== IH: Carburetor, Intake Manifold & Exhaust - Sub-01K ======
 \\
 ===== Bendix Carb Identification =====
@@ Line 115: / Line 115: @@
 ===== Idle Passages =====
-The 36mm carb has 3 idle passages. ((Popgadget of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071986&page=3)) \\
+The 13609A 36mm carb has 3 idle passages. ((Popgadget of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071986&page=3)) \\
-The 38mm carb has 4 idle passages. \\
+The 13609B 36mm carb has 4 idle passages. ((Popgadget of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071986&page=3)) \\
+The 38mm carbs have 4 idle passages. \\
 ===== Main Jet / Idle Tube =====
 One feature of an adjustable main jet, (besides the number), is the holes near the bottom that are drilled at about a 45° angle. ((needspeed of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071986&page=2)) \\
@@ Line 236: / Line 237: @@
   * Dual throttle linkage-spigot mount
   * Fits 1984 Evolution Engines & H-D Twin Cam models 1999 and later.
+====== Parts List ======
+Parts listed from the 1962-1973 Sportster Parts Catalog Supplement (99451-73) \\
+|Part#|Item|Year|
+|1214HW|SCREW, No. 10 x 24 x 3/4" fillister head|1972|
+|3738|BOLT, throttle cable clamp, 1/4" x 28 x 1/2" Hex Head|1972|
+|6316W|WASHER, carburetor to manifold stud, 5/16" x 5/8" x 1/16" (2)|1972|
+|7036|LOCKWASHER, throttle cable clamp bolt 1/4"|1972|
+|7725|LOCKNUT, carburetor to manifold stud, 5/16" x 24 (2)|Late 1972|
+|7739|LOCKNUT, carburetor to manifold stud, 5/16" x 18 (2)|Early 1972|
+|20014-67|STUD, carburetor to manifold (2)|Early 1972|
+|27021-71|INTAKE MANIFOLD|1972|
+|27023-71|GASKET, carburetor to intake manifold|1972|
+|27060-55|0-RlNG, intake manifold (2)|1972|
+|27063-57|CLAMP, with screw and buckle (2)|1972|
+|27065-57|BUCKLE, clamp (2)|1972|
+|27132-71|REPAIR PARTS AND GASKET KIT|1972|
+|27155-72|CARBURETOR|1972|
+|27164-71|ROLL PIN , accelerator pump|1972|
+|27271-71|SCREW, throttle stop, #8-32 slotted hex head|1972|
+|27272-71|SPRING, throttle return|1972|
+|27281-71A|THROTTLE SHAFT AND LEVER|1972|
+|27282-71|THROTTLE PLATE|1972|
+|27326-71|0-RlNG|1972|
+|27341-71|LEVER, accelerator pump|1972|
+|27342-71|SCREW WITH LOCKWASHER, #1/8-40 (4)|1972|
+|27389-71|BOOT, accelerator pump|1972|
+|27396-71|SCREW WITH LOCKWASHER, #4-36|1972|
+|27403-71|WASHER, main jet (fiber)|1972|
+|27404-71|WASHER, idle jet (fiber)|1972|
+|27449-72|BRACKET, throttle cable with clamp|1972|
+|27612-71|MAIN JET, 0.90|1972|
+|27613-71|SPRING, throttle stop screw|1972|
+|27614-71|MAINJET, 0.95mm|1972|
+|27618-71|MAIN JET, 1.00mm|1972|
+|27619-71|MAIN JET, 1.05mm (standard)|1972|
+|27630-71|FLOAT|1972|
+|27631-71|PIN, float|1972|
+|27641-71|IDLE ADJUSTING SCREW|1972|
+|27642-71|SPRING, idle adjusting screw|1972|
+|27645-71|BOWL|1972|
+|27646-71|GASKET, bowl|1972|
+|27659-71|SPRING, float|1972|
+|27663-71|CHOKE PLATE|1972|
+|27664-71|CHOKE SHAFT AND LEVER|1972|
+|27665-71|PIN, choke friction spring|1972|
+|27666-71|FRICTION SPRING, choke|1972|
+|27686-71|SCREW, wire block, #8-36 (2)|1972|
+|27737-71|CLIP, fuel valve|1972|
+|27748-71|FUEL VALVE, with clip|1972|
+|27749-72|IDLE JET|Early 1972|
+|27750-72|IDLE JET|Late 1972|
+|27762-71A|ACCELERATOR PUMP|1972|
+|27763-71|BOWL DRAIN PLUG|1972|
+|33298-65|STUD, carburetor to manifold (2)|Late 1972|
+|38679-72|CLAMP, throttle cable bracket|1972|
+|63578-52|INLET FITIING|1972|
 ====== Bendix / Zenith Manuals and Other Helpful Links ======